Showing 120–130 of 376 results

Audible failure alarmCalls attention to a damaged surge supressor, identifying the need for service. Reduces the time protected equipment is at risk due to compromised surge suppression.Themal overload protectionPrevents thermal run-away when metal oxide varistors (MOVs) become damaged, or when a continuous overvoltage condition exists.Manual disconnect switchEnables the surge supressor to be de-energized for service without disconnecting the protected load.Surge counterRecords the number of power surges the unit is exposed to which can be used as an indicator that the unit is providing protection as intended. A high number of surges can be an indicator of poor facility power quality and the need for additional corrective actionsNEMA 3R/12 enclosureMeets the requirements of a NEMA 3R enclosure for outdoor applications, and a NEMA 12 enclosure for indoor applications.Alarm contactsEnables remote monitoring of TVSS alarm status.Replaceable individual phase modulesSignificantly reduces the time to repair a damaged surge protector, minimizing the time that critical loads are unprotected from transients.Protection Working IndicatorSurgeArrest will warn you if its circuitry has been damaged by heavy strike or power line surge and it is unable to provide 100% protection. If still under warranty, APC will then replace your damaged SurgeArrest free of charge.Noise FilteringSurge Protector attenuates EMI/RFI line noise that can cause data errors and keyboard lockups, ensuring better performance of protected equipment.Lightning and Surge ProtectionTo prevent damage to your equipment from power surges and spikes.

SurgeArrest Panelmount, 480/277V, 120kA/ph, with Surge Counter, Replaceable 3-Phase Brick ModuleNEMA 3R/12 enclosureMeets the requirements of a NEMA 3R enclosure for outdoor applications, and a NEMA 12 enclosure for indoor applications.Noise Filtering120kA SurgeArrest models contain EMI/RFI filtering to reduce line noise that can cause data loss and keyboard errors. 40kA and 80kA units do not contain noise filtering components, so they can be used with powerline networking systems (X10, HomePlug, PLC, etc.).Maximum surge current ratings40kA, 80kA and 120kA per phase maximum surge current ratings, for all your residential, commercial and individual equipment protection needs.Catastrophic Event ProtectionSurgeArrest Panelmount SPDs are equipped with fuses and thermal disconnects that react quickly to protect against dangerous high and low current wiring faults as well as other catastrophic surge events. These panelmount SPDs are passive, and continue to allow power through to your home or building if any of the surge components are damaged.Status Indicator LED'sLED status indicators for each phase and an audible alarm provide immediate failure notification when suppression circuitry has been damaged by a heavy strike or surge.Physical SizeFor easy installation inside your circuit breaker panel (40kA model) or next to your power distribution panels. (80kA and 120 kA models)Chase nipple connectionAllows for mounting of the PM2X units rigidly to the side of your panelboard.

- Calls attention to a damaged surge supressor, identifying the need for service. Reduces the time protected equipment is at risk due to compromised surge suppression.- Prevents thermal run-away when metal oxide varistors (MOVs) become damaged, or when a continuous overvoltage condition exists.- Meets the requirements of a NEMA 4X enclosure for indoor and outdoor applications- Enables remote monitoring of TVSS alarm status.- SurgeArrest will warn you if its circuitry has been damaged by heavy strike or power line surge and it is unable to provide 100% protection. If still under warranty, APC will then replace your damaged SurgeArrest free of charge.- Surge Protector attenuates EMI/RFI line noise that can cause data errors and keyboard lockups, ensuring better performance of protected equipment.- To prevent damage to your equipment from power surges and spikes.- 120kA SurgeArrest models contain EMI/RFI filtering to reduce line noise that can cause data loss and keyboard errors. 40kA and 80kA units do not contain noise filtering components, so they can be used with powerline networking systems (X10, HomePlug, PLC, etc.).- 40kA, 80kA and 120kA per phase maximum surge current ratings, for all your residential, commercial and individual equipment protection needs.SurgeArrest Panelmount SPDs are equipped with fuses and thermal disconnects that react quickly to protect against dangerous high and low current wiring faults as well as other catastrophic surge events. These panelmount SPDs are passive, and continue to allow power through to your home or building if any of the surge components are damaged.- LED status indicators for each phase and an audible alarm provide immediate failure notification when suppression circuitry has been damaged by a heavy strike or surge.- For easy installation inside your circuit breaker panel (40kA model) or next to your power distribution panels. (80kA and 120 kA models)- Allows for mounting of the PM2X units rigidly to the side of your panelboard.

-Game System Organizer and Surge Protection Unit.-Coax Protection. -Data-line Protection.-IEEE let-through rating and UL 1449 compliance.-Noise Filtering. -Surge Protection.