Enhance the performance capabilities of CWDM applications over an OS2 fiber networkOS2 LC to SC Single Mode Duplex Fiber Optic Patch cable facilitates connectivity across 100G networks. It supports Coarse Wavelength Division Multiplexing (CWDM) across an extended wavelength range of 1260-1625nm, improving channel isolation for optimal signal strength over long distances.CompatibilityThis 9/125µm Single Mode fiber cable supports 1260-1625nm laser-optimized sources and is ideal for critical connections between servers, switches, and data center equipment. It is backward compatible with OS1 networks, ensuring a reliable connection in legacy fiber environments.Engineered for Optimal PerformancePrecision-manufactured ceramic ferrules ensure accurate fiber alignment for an insertion loss below 0.3dB. Ultra Physical Contact (UPC)-polished LC to SC fiber ends greatly improve return loss characteristics over older PC polishing techniques. The Bend Insensitive fiber core is surrounded by a layer of low refractive index material. This material reduces the amount of light that can escape the fiber cable by reflecting the light back into the fiber. The OS2 fiber patch cord is engineered for low attenuation and performance that exceeds ITU-T G652.D/G657.A1 and IEC60703-2-50 type B1.3/B6.a1 industry standards.LSZH Cable JacketHoused in a Low-Smoke Zero-Halogen (LSZH) flame-retardant jacket, the OS2 fiber cable emits low smoke and toxic fumes when exposed to extreme heat or in the event of a fire. This enables safer cable installations in areas with poor ventilation including some industrial settings, self-contained environments such as trains and aircraft, as well as residential settings where compliance with building codes must be considered.Each OS2 fiber cable is individually tested for insertion loss performance and includes a test report, for guaranteed compatibility and 100% reliability.The StarTech.com Advantage
Support Higher Bandwidths in Data Networks with OM3 Multimode 50/125 Fiber Patch CableAs the amount of traffic in data networks grows, so does the need for next generation devices and fiber cables to support higher bandwidths. This LC-to-LC multimode fiber optic Ethernet cable is well-suited for 10/40 Gb Ethernet applications up to 300 meters (984 feet) at 850 nm.Use with VCSEL Light Sources for a Cost-Effective, High-Bandwidth SolutionThe N820-10M-TAA is a laser-optimized multimode fiber (LOMMF) cable designed for use with vertical-cavity surface-emitting lasers (VCSELs) and LED lasers to offer a cost-effective, high-bandwidth solution over extended distances in the 850 nm wavelength range. It is commonly used in LANs, SANs and high-speed parallel interconnects for head-ends, central offices and data centers. Experience Reliable Performance with Premium ConstructionPremium materials ensure this multimode fiber cable reliably carries data and voice signals. The N820-10M-TAA has duplex male LC connectors on each end. The aqua OFNP (Optical Fiber Non-Conductive Plenum) jacket is highly fire-resistant, making this cable ideal for plenum areas such as drop ceilings and raised floors. It meets current IEEE 802.3ae and TIA LOMMF standards, and is compatible with existing OM3-rated 50/125 fiber solutions.TAA-Compliant for GSA Schedule PurchasesThe N820-10M-TAA is compliant with the Federal Trade Agreements Act (TAA), which makes it eligible for GSA (General Services Administration) Schedule and other federal procurement contracts.
Manufactured from 62.5/125 duplex (zipcord) fiberPVC jacketLength: 1-meter/Connectors: 2 ST/LC connectors on each endInsertion loss testing performed on every connector (0.2db typical) and provided with cableBeveled edge on ends of glass makes insertion of plug a breezeFiber made from glass (not a polymer)Duplex multimode fiber is most commonly used in LAN applications where links are 10-ft. (3.05 m) or lessFiber optic distributed data interface (FDDI) ratedOFNR (riser rated)
MTP / MPO Push-Pull Connectors for Quick Fiber Optic connectionsPush/Pull tab connectors offer maximum accessibility in high density installations; install / remove with one hand12 times the density of SC style connectorsHigh Density design cuts down on installation costs50/125 OM3 Rated Multimode Fiber, 850nmPlenum rated jacketUnique cable ID label for Quality Control and TraceabilityEach cable 100% tested for low insertion loss and back reflectionTest data supplied with each cableCustom lengths available
Get the performance you demand at a price that makes sense with 9/125 singlemode fiber patch cords from Cables To Go. They provide high bandwidth and transmission rates and support longer distances, but are still cost effective. Perfect for use with today’s high speed networks while providing headroom for tomorrow’s higher bandwidth requirements.- A cost effective solution that provides higher bandwidth and support for longer distances- Perfect for use in Gigabit Ethernet applications- Headroom for tomorrow’s higher bandwidth needs- Lifetime warranty against defects of materials and workmanship- Connectors: (2) ST to (2) SC- Buffer material: PVC- Buffer OD: 900 µm- Jacket material: PVC (OFNR-rated)- Jacket OD: 3.0 mm- Jacket color: Yellow- Attenuation @1310 nm: 1.0 dB/km- Attenuation @1550 nm: 0.75 dB/km- Maximum tensile load: 100 N/cm- Loaded min. bend radius: 5 cm- Unloaded min. bend radius: 3 cm- Crush resistance: 750 N/cm- Impact resistance: 1000 cycles- Flex resistance: 5000 cycles
MFR: Netgear, Inc
Qty: 1
Part #: GS105NA