Showing 560–570 of 572 results

40/100 GbE Cable Supports Higher Bandwidths Needed for High-Density Data NetworkingAs the amount of traffic in data networks grows, so does the need for devices and fiber cables to support higher bandwidths for high-density patching between data center MDFs and IDFs in enterprise installations. This multimode 50/125 OM4 cable is an ideal choice for 100G Ethernet applications up to 100 meters (328 feet) at 1300 nm. It is also backward compatible with 10 Gb, 25 Gb and 40 Gb networks, so you can future-proof your current application for an eventual upgrade to 400 Gb.Magenta Jacket Helps Avoid Misidentification That Can Cause Costly DowntimeThe OM4-rated cable has a magenta jacket to identify it as multimode in a crowded patch panel or switch and prevent it from becoming accidentally disconnected. The OFNP (Optical Fiber Non-Conductive Plenum) jacket is highly fire-resistant, making this cable ideal for plenum areas such as drop ceilings and raised floors. The connectors’ slim boots allow easy one-handed installation and removal of the cable.TAA-Compliant for GSA Schedule PurchasesThe N845B-05M-12MTA is compliant with the Federal Trade Agreements Act (TAA), which makes it eligible for GSA (General Services Administration) Schedule and other federal procurement contracts.

The one-meter N845-01M-12-MG MTP/MPO Multimode Patch Cable supports 40/100 Gb Ethernet speeds and is designed for high-density connections between network equipment in telecommunication rooms and data centers. With two female MTP/MPO connectors, this OM4-rated multimode fiber optic cable is recommended for high-density fiber patching between data center MDFs (main distribution frames) and IDF (intermediate distribution frames). It’s colored magenta for instant identification as an OM4 cable. Base-8 Fiber compatible with both QSFP+ 40GBASE-SR4 and QSFP28 100GBASE-SR4 connections.The 12-fiber MTP/MPO connectors are about the same size as SC connectors, but are 12 times denser, freeing up circuit card and rack space for other cables. The cable is tested for low insertion loss and back reflection on every connector and attenuation loss that meets or exceeds current standards. Push/pull tab connectors are easily accessible in high-density data center applications and make the cable easy to install and remove with one hand. The plenum-rated jacket is perfect for connecting high-speed network components in ceilings, walls and ducts.

9/125 Rated Singlemode Cable for 40/100 Gb Ethernet ApplicationsDesigned for enterprise applications in wiring closets, telecom rooms and data centersRecommended for QSFP+ applications in enterprise installationsPlenum-rated jacket suited for ceilings, walls and ductsYellow-colored for identification as a singlemode cableMTP/MPO APC Connectors with Push/Pull Tabs12-fiber female connectors 12 times denser than SC connectorsAPC connector angled to prevent light from reflecting back into laserPush/pull tabs easy to install and remove with one hand100% tested for low insertion loss and back reflection

OM4-Rated for 40 Gb Ethernet ApplicationsDesigned to extend high-density connections between network equipment in telecommunication rooms and data centersConverts legacy 12-fiber Method C Polarity cables to Method B Polarity for use in Base-8 applicationsSupports speeds up to 40 GbE/100 GbEBackward compatible with existing 50/125 fiberMagenta-colored for identification as an OM4 cableMTP/MPO Connectors with Push/Pull Tab12-fiber male/female connectorsPush/pull tab connector easy to install and remove with one hand100% tested for low insertion loss and back reflectionError-Free Signal Transfer50/125 duplex glass fiber constructionMeets current IEEE 802.3ae and TIA standardsPlenum-rated OFNP jacket perfect for ceilings, walls and ductsJacket features serial number for quality control and traceability

9/125 Rated Singlemode Cable for 40/100 Gb Ethernet ApplicationsDesigned to extend high-density connections between network equipment in telecom rooms and data centersRecommended for patching between data center MDFs and IDFsOptimized for QSFP+ 40GBASE-PLR4 and QSFP28 100GBASE-PSM4 networks6 mm dual plenum-rated jacket and bend-insensitive fiber perfect for ceilings, walls and ductsYellow-colored for identification as a singlemode cableFactory-Terminated MTP/MPO APC Connectors with Push/Pull Tabs8-fiber female connectors 12 times denser than SC connectorsPush/pull tab connectors easy to install and remove with one handAngled connectors prevent light from reflecting back into laser100% tested for low insertion loss and back reflection

9/125 Rated Singlemode Cable for 40/100 Gb Ethernet ApplicationsDesigned to extend high-density connections between network equipment in telecom rooms and data centersRecommended for patching between data center MDFs and IDFsOptimized for QSFP+ 40GBASE-PLR4 and QSFP28 100GBASE-PSM4 networks6 mm dual plenum-rated jacket and bend-insensitive fiber perfect for ceilings, walls and ductsYellow-colored for identification as a singlemode cableFactory-Terminated MTP/MPO APC Connectors with Push/Pull Tabs8-fiber female connectors 12 times denser than SC connectorsPush/pull tab connectors easy to install and remove with one handAngled connectors prevent light from reflecting back into laser100% tested for low insertion loss and back reflection

9/125 Rated Singlemode Cable for 40/100 Gb Ethernet ApplicationsDesigned to extend high-density connections between network equipment in telecom rooms and data centersRecommended for patching between data center MDFs and IDFsOptimized for QSFP+ 40GBASE-PLR4 and QSFP28 100GBASE-PSM4 networks6 mm dual plenum-rated jacket and bend-insensitive fiber perfect for ceilings, walls and ductsYellow-colored for identification as a singlemode cableFactory-Terminated MTP/MPO APC Connectors with Push/Pull Tabs8-fiber female connectors 12 times denser than SC connectorsPush/pull tab connectors easy to install and remove with one handAngled connectors prevent light from reflecting back into laser100% tested for low insertion loss and back reflection

Manufactured from 62.5/125 duplex (zipcord) fiberPVC jacketLength: 1-meter. Connectors: MTRJ to MTRJInsertion loss testing performed on every connector (0.2db typical) and provided with cableBeveled edge on ends of glass makes insertion of plug a breezeFiber made from glass (not a polymer)Duplex multimode fiber is most commonly used in LAN applications where links are typically 10-ft. (3.05 m) or lessFiber optic distributed data interface (FDDI) ratedOFNR (riser rated)

OM4-Rated for 40/100 Gb Ethernet ApplicationsDesigned to extend high-density connections between network equipment in telecom rooms and data centersRecommended for patching between data center MDFs and IDFsOptimized for QSFP+ 40GBASE-SR4 and QSFP28 100GBASE-SR4 networksMagenta-colored for identification as an OM4 cableMTP/MPO Connectors with Push/Pull Tabs8-fiber female connectors 12 times denser than SC connectorsPush/pull tab connectors easy to install and remove with one hand100% tested for low insertion loss and back reflectionError-Free Signal Transfer50/125 duplex glass fiber constructionPlenum-rated jacket and bend-insensitive fiber perfect for ceilings, walls and ducts

9/125 Rated Singlemode Cable for 40/100 Gb Ethernet ApplicationsDesigned to extend high-density connections between network equipment in telecom rooms and data centersRecommended for patching between data center MDFs and IDFsOptimized for QSFP+ 40GBASE-PLR4 and QSFP28 100GBASE-PSM4 networks6 mm dual plenum-rated jacket and bend-insensitive fiber perfect for ceilings, walls and ductsYellow-colored for identification as a singlemode cableFactory-Terminated MTP/MPO APC Connectors with Push/Pull Tabs8-fiber female connectors 12 times denser than SC connectorsPush/pull tab connectors easy to install and remove with one handAngled connectors prevent light from reflecting back into laser100% tested for low insertion loss and back reflection