by Schneider Electric Smart-UPS 2200 VA Tower UPS - Tower - 7 Minute Stand-by - 230 V AC Output - Sine Wave - USB
APC by Schneider Electric Smart-UPS SMT3000I 3000 VA Tower UPS - Tower - 6 Minute Stand-by - 230 V AC Output - Sine Wave - USB - 11 x Battery/Surge Outlet - TAA Compliance
Green modePatent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.Battery failure notificationProvides early-warning fault analysis on batteries enabling timely preventive maintenance.Power-saving outletsAutomatically cuts power to idle equipment to conserve electricity.Resettable circuit breakerEasy recovery from overloads; no need to replace a fuse.LCD displayAlpha-Numeric Display which displays system parameters and alarms.Data-line ProtectionProtection of data lines (Ethernet, Coaxial and Phone lines) ensures complete protection of your equipment from surges. It is very important to protect your equipment from “back door” surges traveling through data lines, as they can be as damaging to your equipment as surges traveling over power lines.Battery-protected and surge-only outletsReserves power capacity and run time for connected equipment that require battery back-up while providing surge only protection for less critical equipment.Cold-start capableProvides temporary battery power when the utility power is out.Hot-swappable batteriesEnsures clean, uninterrupted power to protected equipment while batteries are being replaced.Disconnected battery notificationWarns when a battery is not available to provide backup power.Automatic self-testPeriodic battery self-test ensures early detection of a battery that needs to be replaced.Adjustable voltage-transfer pointsMaximizes useful battery life by widening the input voltage window or tightening the output voltage regulation.Adjustable voltage sensitivityProvides the ability to adapt the UPS for optimal performance in specific power environments or generator applications.Audible alarmsProvides notification of changing utility power and UPS conditions.Transformer-block spaced outletsProtect equipment with input transformer blocks without blocking access to other receptacles.Boost and Trim Automatic Voltage Regulation (AVR)Gives higher application availability by correcting low and high voltage conditions without using the battery.Intelligent battery managementMaximizes battery performance, life, and reliability through intelligent, precision charging.Safety-agency approvedEnsures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.Building Wiring Fault IndicatorThis LED informs users of potentially dangerous wiring problems in the wall circuit.Battery replacement without toolsAllows quick, easy battery replacement.Boost and Trim Automatic Voltage Regulation (AVR)Eliminates voltage fluctuations as a source of AV signal degradation and component power-supply stress.Power conditioningProtects connected loads from surges, spikes, lightning, and other power disturbances.Isolated filter banksEliminates electromagnetic and radio frequency interference (EMI/RFI) as a source of audio-video signal degradation.Dataline Surge ProtectionProvides protection of connected equipment from power surges on the data lines.Safety-agency approvedEnsures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.Resettable circuit breakersEnables a quick recovery from overload events.Multiple mounting methodsAllows for standardization on one product for use in different environments.Front-access servicingSimplifies installation and maintenance while minimizing space requirements.Adjustable voltage sensitivityProvides the ability to adapt the UPS for optimal performance in specific power environments or generator applications.Sequenced turn on/offHelps power on components in the proper order to prevent speaker stress. Proper sequencing can also help manage current draw on startup to prevent unnecessary circuit breaker tripping.LED & display dimmerAdjust the unit's LED and display brightness independently of each other to suit your individual tastes and environment.
Green modePatent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.Battery failure notificationProvides early-warning fault analysis on batteries enabling timely preventive maintenancePower-saving outletsAutomatically cuts power to idle equipment to conserve electricity.Resettable circuit breakerEasy recovery from overloads; no need to replace a fuse.Battery-protected and surge-only outletsReserves power capacity and run time for connected equipment that require battery back-up while providing surge only protection for less critical equipmentCold-start capableProvides temporary battery power when the utility power is out.Serial ConnectivityUse any Home Automation network to monitor and control the S20 through its RS-232 serial port. For information on how to communicate with the S20, see APC's Application Note #102. Crestron and AMX installers should visit their respective websites for information on how to integrate the S20 into those networks.Hot-swappable batteriesEnsures clean, uninterrupted power to protected equipment while batteries are being replacedDisconnected battery notificationWarns when a battery is not available to provide backup power.Dataline Surge ProtectionProvides protection of connected equipment from power surges on the data lines.Automatic self-testPeriodic battery self-test ensures early detection of a battery that needs to be replaced.Adjustable voltage-transfer pointsMaximizes useful battery life by widening the input voltage window or tightening the output voltage regulation.Adjustable voltage sensitivityProvides the ability to adapt the UPS for optimal performance in specific power environments or generator applications.Audible alarmsProvides notification of changing utility power and UPS conditions.User-replaceable batteriesIncreases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR)USB connectivityProvides management of the UPS via a USB port (not available on all models).Serial ConnectivityProvides management of the UPS via a serial port.Transformer-block spaced outletsProtect equipment with input transformer blocks without blocking access to other receptacles.Boost and Trim Automatic Voltage Regulation (AVR)Gives higher application availability by correcting low and high voltage conditions without using the battery.Intelligent battery managementMaximizes battery performance, life, and reliability through intelligent, precision charging.Safety-agency approvedEnsures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.Building Wiring Fault IndicatorThis LED informs users of potentially dangerous wiring problems in the wall circuit.Adjustable voltage sensitivityProvides the ability to adapt the Power Conditioner for optimal performance in specific power environments or generator applications.Battery replacement without toolsAllows quick, easy battery replacement.LCD graphics displayText and mimic diagrams that display modes of operation, system parameters and alarms.
The Back-UPS RS offers high performance protection for your business and office computer systems. It provides abundant battery backup power, allowing you to work through medium and extended length power outages. It also safeguards your equipment from damaging surges and spikes that travel along utility, phone and network lines. A distinguishing feature of the Back-UPS RS is automatic voltage regulation (AVR). AVR instantly adjusts both low and high voltages to safe levels, so you can work indefinitely during brownouts and overvoltage situations, saving the battery for power outages when you need it most. Award-winning shutdown software automatically powers down your computer system in the event of an extended power outage. Additional features like audible alarms, LED status indicators, user replaceable battery, push-button circuit breakers and plentiful outlets (including transformer-block spaced outlets) make the Back-UPS RS the perfect unit to protect your business' productivity from the constant threat of power problems and lost data. Green mode: Patent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.Audible alarms: Provide notification of changing flywheel conditionsBattery failure notification: Provides early-warning fault analysis on batteries enabling timely preventive maintenancePower-saving outlets: Automatically cuts power to idle equipment to conserve electricity.LCD display: Alpha-Numeric Display which displays system parameters and alarms.Battery-protected and surge-only outlets: Reserves power capacity and run time for connected equipment that require battery back-up while providing surge only protection for less critical equipmentCold-start capable: Provides temporary battery power when the utility power is out.Hot-swappable batteries: Ensures clean, uninterrupted power to protected equipment while batteries are being replacedAutomatic self-test: Periodic battery self-test ensures early detection of a battery that needs to be replaced.Adjustable voltage sensitivity: Provides the ability to adapt the UPS for optimal performance in specific power environments or generator applications.Audible alarms: Provides notification of changing utility power and UPS conditions.User-replaceable batteries: Increases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR)USB connectivity: Provides management of the UPS via a USB port (not available on all models).Transformer-block spaced outlets: Protect equipment with input transformer blocks without blocking access to other receptacles.Boost and Trim Automatic Voltage Regulation (AVR): Gives higher application availability by correcting low and high voltage conditions without using the batteryAutomatic Voltage Regulation (AVR): Gives higher application availability by correcting low and high voltage conditions without using the battery.Intelligent battery management: Maximizes battery performance, life, and reliability through intelligent, precision charging.Building Wiring Fault Indicator: This LED informs users of potentially dangerous wiring problems in the wall circuit.Adjustable voltage sensitivity: Provides the ability to adapt the Power Conditioner for optimal performance in specific power environments or generator applications.Automatic Voltage Regulation (AVR): Automatically steps up low voltage and steps down high voltage to levels that are suitable for your equipment.Battery fault detection: Monitors room and individual battery temperature changes for early detection of thermal runaway, shorted cells, open circuit, and bad battery.Battery-protected and surge-only outlets: Reserves power capacity and run time for connected equipment that require battery back-up while providing surge only protection for less critical equipment.Safety-agency approved: Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment. Power conditioning: Protects connected loads from surges, spikes, lightning, and other power disturbances. Audible alarms: Provides notification of changing utility power and UPS conditions. Automatic restart of loads after UPS shutdown: Automatically starts up the connected equipment upon the return of utility power. Automatic self-test: Periodic battery self-test ensures early detection of a battery that needs to be replaced.Battery replacement without tools: Allows quick, easy battery replacement. LED status indicators: Quickly understand unit and power status with visual indicators. Cold-start capable: Provides temporary battery power when the utility power is out. Hot-swappable batteries: Ensures clean, uninterrupted power to protected equipment while batteries are being replaced Resettable circuit breakers: Enables a quick recovery from overload events. Transformer-block spaced outlets: Protect equipment with input transformer blocks without blocking access to other receptacles. User-replaceable batteries: Increases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR) Adjustable voltage sensitivity: Provides the ability to adapt the UPS for optimal performance in specific power environments or generator applications. Adjustable voltage-transfer points: Maximizes useful battery life by widening the input voltage window or tightening the output voltage regulation. Intelligent battery management: Micro-processor controlled battery charging and diagnostic testing ensures maximum battery life.
Boost and Trim Automatic Voltage Regulation (AVR) Gives higher application availability by correcting low and high voltage conditions without using the battery. Intelligent Battery Management Maximizes battery performance, life, and reliability through intelligent, precision charging. Power conditioning Protects connected loads from surges, spikes, lightning, and other power disturbances. Temperature-compensated battery charging Prolongs battery life by regulating the charge voltage according to battery temperature. Automatic restart of loads after UPS shutdown Automatically starts up the connected equipment upon the return of utility power. Automatic self-test Periodic battery self-test ensures early detection of a battery that needs to be replaced. Cold-start capable Provides temporary battery power when the utility power is out. Disconnected battery notification Warns when a battery is not available to provide backup power. Generator Compatible Ensures clean, uninterrupted power to protected equipment when generator power is used. Network manageable Provides remote management of the UPS over the network. SmartSlot Customize UPS capabilities with management cards. Audible Alarms Actively let you know if the unit is on battery, if the battery is low or if there is an overload condition. LED status indicators Quickly understand unit and power status with visual indicators. Serial Connectivity Provides management of the UPS via a serial port. USB Connectivity Provides management of the UPS via a USB port (not available on all models). Disconnected battery notification Warns when a battery is not available to provide backup power. InfraStruXure Manager Compatible Enables centralized management via the APC InfraStruXure Manager. User-replaceable batteries Increases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR) Hot-swappable batteries Ensures clean, uninterrupted power to protected equipment while batteries are being replaced Predictive failure notification Provides early-warning fault analysis ensuring proactive component replacement. Resettable circuit breakers Enables a quick recovery from overload events. Adjustable voltage-transfer points Maximizes useful battery life by widening the input voltage window or tightening the output voltage regulation. Adjustable voltage sensitivity Provides the ability to adapt the UPS for optimal performance in specific power environments or generator applications. Field-replaceable power distribution panel Ensures compatibility with equipment that has different plug types.
Wrap Around System Bypass(3) Breaker maintenance bypass panel to isolate the UPS from the critical loa.- APC Smart-UPS Accessories , Input: 200V, 208V, 220V, 230V, 240V, 380V 3PH, 400V 3PH- Input Connections: Hard Wire 3-wire (2PH + G), Hard Wire 3 wire (1PH+N+G), Hard Wire 5-wire (3PH + N + G)- Output: 200V, 208V, 220V, 230V, 240V- Output Connections: Hard Wire 3-wire (2PH + G), Hard Wire 3-wire (H N + G)
Battery failure notificationProvides early-warning fault analysis on batteries enabling timely preventive maintenanceLED IndicatorsProvide easy-to-read status of the unit and utility power conditions.Resettable circuit breakerEasy recovery from overloads; no need to replace a fuse.Battery-protected and surge-only outletsReserves power capacity and run time for connected equipment that require battery back-up while providing surge only protection for less critical equipmentCold-start capableProvides temporary battery power when the utility power is out.Hot-swappable batteriesEnsures clean, uninterrupted power to protected equipment while batteries are being replacedDisconnected battery notificationWarns when a battery is not available to provide backup power.Dataline Surge ProtectionProvides protection of connected equipment from power surges on the data lines.Automatic self-testPeriodic battery self-test ensures early detection of a battery that needs to be replaced.Audible alarmsProvides notification of changing utility power and UPS conditionsUser-replaceable batteriesIncreases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR)USB connectivityProvides management of the UPS via a USB port (not available on all models).Transformer-block spaced outletsProtect equipment with input transformer blocks without blocking access to other receptacles.Intelligent battery managementMaximizes battery performance, life, and reliability through intelligent, precision charging.Safety-agency approvedEnsures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.Battery replacement without toolsAllows quick, easy battery replacement.
Audible alarms Provides notification of changing utility power and UPS power conditions Automatic self-test Periodic battery self-test ensures early detection of a battery that needs to be replaced. Battery failure notification Provides early-warning fault analysis on batteries enabling timely preventive maintenance Battery replacement without tools Enables fast battery replacement, lowering Mean Time to Repair (MTTR). Battery-protected and surge-only outlets Reserves power capacity and run time for connected equipment that require UPS battery back-up while providing surge only protection for less critical equipment Cold-start capable Provides temporary battery power when the utility power is out. Dataline surge protection Provides protection of connected equipment from power surges on the data lines. Disconnected battery notification Warns when a battery is not available to provide backup power. Hot-swappable batteries Ensures clean, uninterrupted power to protected equipment while batteries are being replaced Intelligent battery management Maximizes battery performance, life, and reliability through intelligent, precision charging. Resettable circuit breaker Easy recovery from overloads; no need to replace a fuse. (Not available on Wall Tap SKUs) Safety-agency approved The UPS is UL1778 Listed Transformer-block spaced outlets Protect equipment with input transformer blocks without blocking access to other receptacles USB connectivity Provides management of the UPS via a USB port (not available on all models). User-replaceable batteries Increases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair (MTTR)
APC Back-UPS. UPS topology: Standby (Offline), Output power capacity: 0.7 kVA, Output power: 405 W. AC outlet types: Type F. Battery technology: Sealed Lead Acid (VRLA), Battery capacity: 9 Ah, Battery capacity: 86 VAh. Form factor: Compact, Product color: Black, Cable length: 72"" (1.83 m). Width: 8.82"" (224 mm), Depth: 12.2"" (311 mm), Height: 3.5"" (89 mm)
MFR: Netgear, Inc
Qty: 1
Part #: GS105NA